Power Supply User Manual
10DCV 24.0 - This displays the DC voltage at the color changer.[ /Enter]Pos 000 - This displays the actual position of the gelstring. If the color cha
11Ver x.x - This tells you the software version installed in the color changer set to the channel you are looking at.[ /Enter]Identify - Pressing [ -]
12Identify - Pressing [ -] will cause the gobo changer, whose status you are viewing, to initialize.SETUPThis menu is used to display and select the s
13The following two screens will be displayed only if the DMX fan option is turned on.[ /Enter]FChn 025 - This allows you to set the DMX fan control c
14If an alert has been triggered with the presence of DMX signal, you will see the display (the second - changes to a + ) as follows:001 - + 048If a
15Pos - This allows you to move the gelstring or gobo carrier independently from the lighting console.[ /Enter]Fan - This allows you to change the fan
163. Connect the Power Supply to AC powerPlug the AC cord into a non-dimmed power circuit. The power supply automatically accommodates 100 - 132 VAC (
17Fan speed (when enabled at the power supply) is remotely controlled with the following DMX levels:51% to 100% -- fan at normal (high) speed0% to 50%
18Refer to the user manual of the various Coloram II System components for detailed head-feet information on those products."Head-Feet" Exam
19Follow these steps to install the hanger bracket.1. Disconnect AC power from the power supply.2. Place the power supply on its side on a flat surfac
219000 – 24-Way Coloram Power Supply (600 watts)19012 – 12-Way Coloram Power Supply (300 watts)19060 – 6-Way Coloram Power Supply (150 watts)Softwa
20Power supply rack mountingThe Coloram II Power Supply rack mount accessory can be used with up to two Coloram II Power Supplies and allows them to b
21Equipment CompatibilityThe following is a chart of compatibility and capacity of the various models of Coloram II Power Supply and the companion com
22DMX512 control cableThe DMX control cable from the lighting board to the power supply is a five conductor cable with 5-pin XLR connectors on each en
23Software Version ChangesThe changes for power supply software version 3.0 from previous software versions are summarized below.1. Added menus tree i
24The Coloram II Cable7042-3... 3' power/signal cable7042-5...
25Warranty informationWYBRON, INC. warrants to the original owner or retail customer that for a period of one year from date of delivery of a portable
3SAVE THESE INSTRUCTIONSREAD AND FOLLOW ALL INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSThis manual gives step-by-step instructions for preparation, setu
4Introduction The Coloram II System consists of scrolling color changers, mixing color changers, dowsers, other products and power supplies in a wide
5DMX CONSOLEDMX512DMX Control consoleAC PowerGoboram II Gobo ChgrColoram IIColor ChangerTo additionalColor Changersor Gobo ChgrsColoram IIPower Supply
6Power SupplyThe power supply converts the DMX512 signal level from the lighting console into Coloram I/Coloram II control signal which it then sends
7XX UNITSSETUPOPTIONSSHUTDOWNSEND ?SEND ? POS ? XXXCOMMANDSYESNOYESNO+-NORMLOWOFFNORMLOWDISP ?DEC%HEX1 -- XDMX OK*ALERT*CHAN ?MODE ?JTTR ?TBCK ?Chan 0
8RUN SCREEN LOOPThe display alternates between three screens. The first is "1 -- X" where X is highest DMX channel used by a color changer
9It is important to note that if the power supply is at its current limit (but not exceeded), it will not "check in" any other units and the
Komentáře k této Příručce